Titre de série : | Mémoire FPL Master d’ingénierie Génie Civil | Titre : | Etude technique détaillée d’un hôtel « cinq étoiles de niveau R+5 » dans la ville de Fada N’gourma / Burkina Faso | Type de document : | texte imprimé | Auteurs : | Nassour Chérif MAHAMAT | Année de publication : | 2015 | Importance : | 201 p. | Langues : | Français (fre) | Résumé : | Ce présent rapport sanctionne un projet de fin d’étude en vue de l’obtention du master en ingénierie de l’eau et de l’environnement à 2iE. L’objectif visé par ce projet est de concevoir et dimensionner un bâtiment R+5 à usage d’hôtel. L’étude est focalisée sur le dimensionnement des différents éléments de la structure, on décide de sectionner notre structure en deux niveaux comme suit : le niveau rez-de-chaussée est utilisé pour tous les autres services de traitement de l’hôtel et les étages courants sont exclusivement utilisés pour les chambres de l’hôtel (suite et single). L’enceinte s’étend sur une surface totale de 60 m×80 m=4800 m^2 et bâtis sur une aire de 36.4 m×26.4 m=960.96 m² avec une hauteur totale de : 20.2 m. Le bâtiment est constitué des structures porteuses en béton armé dalles, poutres et poteaux reposant sur des semelles isolées. Les prescriptions techniques utilisées sont les règles BAEL 91 révisées 99, le DTU 13.12, le cahier des prescriptions techniques (CPT) et la norme française NFP-06 004. La première phase de calcul est basée sur le pré dimensionnement de tous les éléments de la structure, vient ensuite la descente des charges sur les poteaux et fondations et enfin le dimensionnement des éléments porteurs et non porteurs de l’ouvrage. Tous ces calculs ont été faits manuellement à l’ELU puis vérifiés à l’ELS. Au terme de l’étude, un dossier d’exécution a été établi, dans lequel tous les détails de ferraillage ont été fournis.
Abstractr : This present report sanctions an end of study project with a view to obtaining a master’s degree in water and environmental engineering at 2iE. The objective of this project is to design and size an R+5 building for hotel use. The study is focused on the dimensioning of the various element of the structure, we decide to section our structure in two levels as follows: the ground floor level is used for all other treatment service of the hotel and the current floors are exclusively used for the hotel rooms (suite and single). The enclosure extends over a total surface : 60 m×80 m=4800 m^2, with a total height of 20.2 m. the building consists of load-bearing structures in reinforced concrete slabs, beams, and posts resting on insulated footings. The technical prescriptions used are the rules BAEL 91, revised 99, the DTU 13.12, the technical prescription book (CPT) and the french standard NFP-06 004. The first calculation phase in based on the pre dimensioning of all the elements of the structure, then comes the descent of the loads on the posts and foundations and finally the dimensioning of the load-bearing and non-load bearing elements of the structure. All of these calculations were done manually at the ELU, then revirified at the ELS.At the end of the study, an execution file was established, in which all the details of reinforcement were provited. |
Mémoire FPL Master d’ingénierie Génie Civil. Etude technique détaillée d’un hôtel « cinq étoiles de niveau R+5 » dans la ville de Fada N’gourma / Burkina Faso [texte imprimé] / Nassour Chérif MAHAMAT . - 2015 . - 201 p. Langues : Français ( fre) Résumé : | Ce présent rapport sanctionne un projet de fin d’étude en vue de l’obtention du master en ingénierie de l’eau et de l’environnement à 2iE. L’objectif visé par ce projet est de concevoir et dimensionner un bâtiment R+5 à usage d’hôtel. L’étude est focalisée sur le dimensionnement des différents éléments de la structure, on décide de sectionner notre structure en deux niveaux comme suit : le niveau rez-de-chaussée est utilisé pour tous les autres services de traitement de l’hôtel et les étages courants sont exclusivement utilisés pour les chambres de l’hôtel (suite et single). L’enceinte s’étend sur une surface totale de 60 m×80 m=4800 m^2 et bâtis sur une aire de 36.4 m×26.4 m=960.96 m² avec une hauteur totale de : 20.2 m. Le bâtiment est constitué des structures porteuses en béton armé dalles, poutres et poteaux reposant sur des semelles isolées. Les prescriptions techniques utilisées sont les règles BAEL 91 révisées 99, le DTU 13.12, le cahier des prescriptions techniques (CPT) et la norme française NFP-06 004. La première phase de calcul est basée sur le pré dimensionnement de tous les éléments de la structure, vient ensuite la descente des charges sur les poteaux et fondations et enfin le dimensionnement des éléments porteurs et non porteurs de l’ouvrage. Tous ces calculs ont été faits manuellement à l’ELU puis vérifiés à l’ELS. Au terme de l’étude, un dossier d’exécution a été établi, dans lequel tous les détails de ferraillage ont été fournis.
Abstractr : This present report sanctions an end of study project with a view to obtaining a master’s degree in water and environmental engineering at 2iE. The objective of this project is to design and size an R+5 building for hotel use. The study is focused on the dimensioning of the various element of the structure, we decide to section our structure in two levels as follows: the ground floor level is used for all other treatment service of the hotel and the current floors are exclusively used for the hotel rooms (suite and single). The enclosure extends over a total surface : 60 m×80 m=4800 m^2, with a total height of 20.2 m. the building consists of load-bearing structures in reinforced concrete slabs, beams, and posts resting on insulated footings. The technical prescriptions used are the rules BAEL 91, revised 99, the DTU 13.12, the technical prescription book (CPT) and the french standard NFP-06 004. The first calculation phase in based on the pre dimensioning of all the elements of the structure, then comes the descent of the loads on the posts and foundations and finally the dimensioning of the load-bearing and non-load bearing elements of the structure. All of these calculations were done manually at the ELU, then revirified at the ELS.At the end of the study, an execution file was established, in which all the details of reinforcement were provited. |
|